Share this story Share on Facebook icon Share on Twitter icon Share on Pinterest icon Share on Google Plus icon Share on Linked In icon Share via Email icon

How to model loads for model railway wagons


Coal might have been the lifeblood of the railway's freight services, but it wasn't the only commodity carried. Until 1962, the railways were designated 'Common Carriers' which meant they weren't allowed to turn down any load offered, no matter how awkward, at a nationally agreed rate.

Everything from food to building materials to racing pigeons was moved by rail. Much of this was stacked in box vans and so from a modellers' point of view, invisible. However, there were still plenty of open wagons and they needed to be kept full if they were to make money for the company.

Picking suitable loads for a model railway isn't as easy as you might think. All those lovely colourful private owner wagons would normally be full of coal, so putting anything else in them can require a little 'modellers' licence'. In other words, we've stretched the truth a bit to make our layout a bit more interesting but a little lateral thinking can provide suitable ideas.

Open wagons with loads give any model railway a sense of purpose. We're not just running trains around, we're operating a real service. Just like the real thing.


Modelling pipes


For OO gauge models, drinking straws are perfect for the job. Start by cutting them to length. Then cut a thin slice, around 3mm long for the collar at one end. Slide this over the end of the straw, fixing with superglue.
Pipes for model railway wagons


The pipes are glued with all-purpose adhesive to a piece of card cut to fit the inside of your wagon. If the gaps in the collars are placed at the bottom, no one will ever know they are there. Spray the load with red oxide coloured car primer. Hold the can several centimetres further away from the model than the instructions tell you. This way the paint is slightly dry when it hits the pipes giving a slightly rough look to replicate clay.
Pipes for model railway wagons glued together


To protect the pipes in transit, straw would be packed around them. We've used beige electrostatic grass pushed into place but any fibrous material will work fine such as wool cut into short lengths.
Pipes placed in model railway wagon


Modelling a plank load


Planks start life as wooden coffee stirrers. Cut to around 5cm long and then sand the ends square. Then, using a sharp knife and steel rule, split in half along their length to give planks 2-3mm wide, just over a scale 6 inches.
cutting coffee stirrers for model railway wagon load


Build up around 3 layers of planks using PVA glue to hold them together. We find it easiest to work with the pieces in the wagon but remove the load before the glue is fully dry to make sure it's not fixed permanently.
Gluing together wooden planks for oo gauge wagon


It's important that the ends of the planks don't stick out any further than the buffer faces. If this happens, on the real railway, a low empty wagon would be coupled up to stop the load hitting the next vehicle in the train. You could do this, but it makes marshalling the wagons trickier.
wooden plank load added to wagon

Modelling a tarpaulin-covered load



To keep the British weather at bay, most open wagons travelled with a tarpaulin cover. Sadly, the only way to replicate this is to stick the sheet in place. As you can't tell what is in there, running the same wagon both to and from a destination doesn't look wrong – there could be something different under there for the return trip. OO scale tarpaulins are 86mm by 60mm. We're using a pre-printed Smiths sheet from Wizard models, but plain grey paper works just as well or you can download versions to print yourself from some suppliers.
oo gauge model railway wagon tarpaulin


To give the load a little shape, some foam is glued in the wagon. This isn't essential as some loads were lower than the sides, leaving the tarpaulin to dip in the middle, but supporting the paper isn't a bad idea or it's easy to poke your finger through it!
Adding model railway tarpaulin to a wagon


Arrange the sheet so it's centred on the wagon and glue to the sides with all-purpose adhesive or thick superglue. Leave to dry before the next step.
Glue tarpaulin onto model railway wagon


The ends are folded around much like wrapping a parcel and glued in place. On the real wagon, ropes would be used to tie everything down and you can use black thread to represent these if you like, although on a layout you don't really miss them.
the completed wagon with tarpaulin


These are just three, fairly ways in which to add varying loads to model railway wagons. The possibilities are endless. Next time your on the railway, keep an eye out for what loads are being carried and then try to replicate tem on your own model railway. Good luck...

If you want to learn how to weather wagons, click here to read one of the many 'Technique' articles on World of Railways.

Back to "Other" Category

09/01/2019 Share this story   Share on Facebook icon Share on Twitter icon Share on Pinterest icon Share on Google Plus icon Share on Linked In icon Share via Email icon

Recent Updates

Top tips on how to model roads and road markings

Here we show you our top six tips on how to model roads, road markings and signs. ...

Model Railway Tools for Beginners

We take a look at the top model railway tools and equipment needed to help you get started. ...

Weathering Model Trains. Top Tips and Techniques

We reveal top tips and techniques for weathering model trains. ...

Model Railway Scales and gauges explained

What's the difference between scale and gauge in model railways? Here's our guide to understanding model ...

Other Articles

How to model wagon loads for mining areas

We take a look at suitable loads for mining areas. Coal is an obvious choice, but coke, stone, ballast and ...

VIDEO: Creating model railway bushes with Woodland Scenics

Watch the experts at Woodland Scenics show you how to create shrubs and bushes. ...

A complete guide to model railway baseboard construction

A step-by-step guide to model railway baseboard construction demonstrating how easy it can be to build the ...

How to fit DCC sound into a Dapol N Gauge 'Hall'

We show you how to fit DCC Sound into an N gauge Dapol GWR ‘Hall’ 4-6-0. ...